Finding Configuration Details Quickly in Cisco IOS

Finding the right piece of information that you need from a Cisco router can often be a challenge. For example, if you use the show running-config command on a large production router, you can end up with 25 pages of text output.

Locating that one piece of information you’re looking for can take a lot of time. Once you find it, you might need to make a change, only to have to rerun the command and go through the whole process again.

However, there are some shortcuts you can take to find this information more quickly. Let’s looks at some filtering options you can use when maneuvering through long command output on a Cisco router.

Filter output using line numbers

You can use the ‘show running-config linenum’ command to configure the system to include line numbers at the start of each line in the output. Here’s an example:

Current configuration : 59161 bytes 1 : ! 2 : ! Last configuration change at 09:25:35 CDT Tue Aug 16 2005 by root 3 : ! NVRAM config last updated at 09:25:36 CDT Tue Aug 16 2005 by root 4 : ! 5 : version 12.3 6 : service tcp-keepalives-in 7 : service tcp-keepalives-out 8 : service timestamps debug datetime msec localtime show-timezone 9 : service timestamps log datetime msec localtime show-timezone 10 : service password-encryption

Once you have line numbers to use as reference points, you can then filter the output by starting at a certain line or only returning a specified line. Here’s an example of starting the output at a specific line:

Cell_Router# show running-config linenum | begin 6 :
6 : service tcp-keepalives-in
7 : service tcp-keepalives-out
8 : service timestamps debug datetime msec localtime show-timezone
9 : service timestamps log datetime msec localtime show-timezone
10 : service password-encryption

Here’s an example of requesting only one line returned in the output:

Cell_Router# show running-config linenum | include ( 6 : )
6 : service tcp-keepalives-in

Filter output using Include, Exclude, or Begin

You can also use certain commands to help filter your output. For example, you can use the include command to see only lines that include the wordservice. Here’s an example:

Cell_Router# show running-config | include serviceservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption

You can use the begin command to start the output at a certain line (such as an interface). Here’s an example:

Cell_Router# show running-config | begin interface Serial3/0
interface Serial3/0
description MPLS T-1
bandwidth 1544
ip address 10.0.100.2 255.255.255.252
no ip proxy-arp(truncated)

In addition, you can use the exclude command in the same way if there’s something particularly long that you don’t need to see in the output.

The best thing about these three commands is that they work with almost any output on the router. For example, let’s say I wanted to see all routes that begin with the IP address 10.83.x.x. But it doesn’t work if I use this:

Cell_Router# show ip route 10.83.0.0
% Subnet not in table

However, if I use something like the following example, I can see all of the routes that begin with 10.83.x.x:

Cell_Router# show ip route | include 10.83.
O 10.83.100.8/30 [110/2370] via 10.83.100.2, 05:32:27, Serial1/2:0.83
O 10.83.100.4/30 [110/2115] via 10.20.100.2, 05:32:27, Serial1/2:0.2
C 10.83.100.0/30 is directly connected, Serial1/2:0.83
O 10.83.103.0/24 [110/2195] via 10.83.100.2, 05:32:27, Serial1/2:0.83

Filter output by interface

On the other hand, if you only need to see the output of one specific interface, you can also filter output in that way. Here’s an example:

Cell_Router# show running-config interface Serial3/0
Building configuration…
Current configuration : 209 bytes!
interface Serial3/0
description MPLS T-1
bandwidth 1544
ip address 10.0.100.2 255.255.255.252
no ip proxy-arp
no ip mroute-cache
no fair-queue
no cdp enable
end

Start searching your output

Did you know that you can search directly from the show running-config command’s output? If you use the show running-config command, you should see a “More” prompt at the end of each page of output (depending on your page length).

If you enter a forward slash [/] at this prompt, it will replace the prompt with the slash, and you can then type in whatever you want to search for. Press [Enter], and it will say filtering and then begin showing you the results of your search. (This is exactly how the UNIX pg command works.) Here’s an example:

/interface Serial3/0
filtering…
interface Serial3/0
description MPLS T-1
bandwidth 1544
ip address 10.0.100.2 255.255.255.252

Mastering the IOS command structure and modifiers will help you to find information quickly and efficiently.

We hope this helps.

Leave a Comment

Contact Us Here


Please verify.
Validation complete :)
Validation failed :(
 
Your contact request has been received. We usually respond within an hour, but please be patient. We will get back to you very soon.
Scroll to Top